Crafts experience

〜I built a motorcycle based on Prince's "Purple Rain" in Japan, so I'll show you the process of making it.〜

English edition

Building Prince’s Purple Rain Motorcycle Replica (Honda CM400T Custom) in japan- No. 4

投稿日：2026年3月2日 更新日：



I’m building a motorcycles for Prince “Purple Rain”（No. 4）

☆Click here for the First article ☆
☆Click here for the completed motorcycle☆

This time, following the last cowling modification, we processed the gasoline tank.　The first step is to remove the paint on the gas tank.

プリンスパープルレイン　バイク　prince purplerain　motorcycle

Pour zinc paint to prevent the gas tank from rusting.

プリンスパープルレイン　バイク　prince purplerain　motorcycle

A special solvent is used to remove the paint.

プリンスパープルレイン　バイク　prince purplerain　motorcycle

The paint will peel off immediately, so scrape it off with a scraper.

プリンスパープルレイン　バイク　prince purplerain　motorcycle

After removing all the paint, put putty on the dented part and scrape it off. Also fill in the dent where the Honda emblem will be attached and flatten it.　After that, spray the surfacer.

オイルレスコンプレッサー

This is the compressor I use all the time.

エアスプレーガン等

This is the spray gun I use all the time.

塗装用具

Other painting tools.

プラサフ

塗装用マスク

And the important thing is this painting mask.

プリンスパープルレイン　バイク　prince purplerain　motorcycle

I sprayed the surfacer.

プリンスパープルレイン　バイク　prince purplerain　motorcycle

プリンスパープルレイン　バイク　prince purplerain　motorcycle

There were still many dents, so I added putty again and scraped it off.

プリンスパープルレイン　バイク　prince purplerain　motorcycle

Next, make the side covers.

プリンスパープルレイン　バイク　prince purplerain　motorcycle

Strip the original paint.

プリンスパープルレイン　バイク　prince purplerain　motorcycle

The side cover of “CM400E” had strong paint and was hard to scrape off.

プリンスパープルレイン　バイク　prince purplerain　motorcycle

In order to bring the corners of the cowling closer to the ideal shape, we made modifications until we were satisfied.
Dig the edge with a chisel and paste the plating molding for automobiles on the edge.

 

プリンスパープルレイン　バイク　prince purplerain　motorcycle

It’s an ideal shape.

プリンスパープルレイン　バイク　prince purplerain　motorcycle

Spray the surfacer again.

プリンスパープルレイン　バイク　prince purplerain　motorcycle

プリンスパープルレイン　バイク　prince purplerain　motorcycle

プリンスパープルレイン　バイク　prince purplerain　motorcycle

プリンスパープルレイン　バイク　prince purplerain　motorcycle

Clean up. Don’t you think it’s close to the image of “Purple Rain”?



～archive～
☆Click here for the completed motorcycle☆
Building a Prince’s “Purple Rain” motorcycle Replica㉑
Building a Prince’s “Purple Rain” motorcycle Replica⑳
Building a Prince’s “Purple Rain” motorcycle Replica⑲
Building a Prince’s “Purple Rain” motorcycle Replica⑱
Building a Prince’s “Purple Rain” motorcycle Replica⑰
Building a Prince’s “Purple Rain” motorcycle Replica⑯
Building a Prince’s “Purple Rain” motorcycle Replica⑮
Building a Prince’s “Purple Rain” motorcycle Replica⑭
Building a Prince’s “Purple Rain” motorcycle Replica⑬
Building a Prince’s “Purple Rain” motorcycle Replica⑫
Building a Prince’s “Purple Rain” motorcycle Replica⑪
Building a Prince’s “Purple Rain” motorcycle Replica⑩
Building a Prince’s “Purple Rain” motorcycle Replica⑨
Building a Prince’s “Purple Rain” motorcycle Replica⑧
Building a Prince’s “Purple Rain” motorcycle Replica⑦
Building a Prince’s “Purple Rain” motorcycle Replica⑥
Building a Prince’s “Purple Rain” motorcycle Replica⑤
Building a Prince’s “Purple Rain” motorcycle Replica④
Building a Prince’s “Purple Rain” motorcycle Replica③
Building a Prince’s “Purple Rain” motorcycle Replica②
Building a Prince’s “Purple Rain” motorcycle Replica①

-English edition

執筆者：

comment

Your email address will not be published. Required fields are marked *

CAPTCHA


関連記事

Building Prince’s Purple Rain Motorcycle Replica (Honda CM400T Custom) in japan- No. 13

I’m building a motorcycles for Prince “Purple Rain”（No. 13） ☆Click here for the First article ☆ ☆Click here for the completed motorcycle☆ Last time I made a sissy bar and cowling stay.　I installed a spacer because there was a gap between the sissy bar stay and the main body. Fits without gaps.　The sissy bar fitting is now complete.　After that, just send it to the plating shop. Cut the excess part of the cowl stay to give a sharp impression. Install headlights.　Ported from the conventional cowling. The shape of the light stay differs depending on the type of “Windjammer”.　The “Windjammer 4” …

Building Prince’s Purple Rain Motorcycle Replica (Honda CM400T Custom) in japan- No. 17

I’m building a motorcycles for Prince “Purple Rain”（No. 17） ☆Click here for the First article ☆ ☆Click here for the completed motorcycle☆ I’m having trouble making a sheet.　It’s my first initiative, and I’m making progress little by little while looking for ways to do it. Fix the carbon pipe backrest made last time to the seat base. Many layers of FRP are layered and hardened. Paste FRP on the back for reinforcement.　Originally, it would be better to make the backrest from an iron plate, but I made it from FRP because it does not fit two people and it has …

Building Prince’s Purple Rain Motorcycle Replica (Honda CM400T Custom) in japan- No. 9

I’m building a motorcycles for Prince “Purple Rain”（No. 9） ☆Click here for the First article ☆ ☆Click here for the completed motorcycle☆ Last time I finished working on the exterior. This time it is wiring adjustment, cowling stay adjustment, sissy bar work. Wrap the wiring near the headlight with food wrap.　It is waterproof. Then wrap it in a plastic sheet for gardening. compact. The mounting position of the cowl and stay is slightly misaligned, so adjustment is required. Take a mold with aluminum foil and make a spacer. I’m thinking of a light and soft spacer. Cut off the excess …

prince-purple-rain-motorcycle-honda-cm400-build

Building Prince’s Purple Rain Motorcycle Replica (Honda CM400T Custom) in japan- No. 20

I’m building a motorcycles for Prince “Purple Rain”（No. 20） ☆Click here for the First article ☆ ☆Click here for the completed motorcycle☆ This time the sheet is complete. This time, I painted the diamond mark on the seat and covered the seat.   It turned bright red. Sew in a diamond shape.　Sew with the sponge in between. The surface was wrinkled. It’s behind the seat base. I sprayed it with a rust preventative. Add molding to the edges to prevent the sheet from tearing. Cover with vinyl to prevent water from entering. It is difficult to stretch the sheet. It’s …

Building Prince’s Purple Rain Motorcycle Replica (Honda CM400T Custom) in japan- No. 14

I’m building a motorcycles for Prince “Purple Rain”（No. 14） ☆Click here for the First article ☆ ☆Click here for the completed motorcycle☆ I thought there was no part to fix the headlight lens, but there was. It seems to cover this ring from the top of the lens and fix it with a screw.　I didn’t know this method last time. Finally, attach the headlight to the cowling.　Mask the cowling so that it is not damaged. It has a unique retro feel not found in recent motorcycles.　It’s like a living creature. Next, install the side blinkers.　This “Windjammer 2” had a side …

PREV
Building Prince's Purple Rain Motorcycle Replica (Honda CM400T Custom) in japan- No. 3
NEXT
Building Prince's Purple Rain Motorcycle Replica (Honda CM400T Custom) in japan- No. 5