Crafts experience

〜I built a motorcycle based on Prince's "Purple Rain" in Japan, so I'll show you the process of making it.〜

English edition

Building Prince’s Purple Rain Motorcycle Replica (Honda CM400T Custom) in Japan – No. 20

投稿日：2026年3月3日 更新日：



I’m building a motorcycles for Prince “Purple Rain”（No. 20）

☆Click here for the First article ☆
☆Click here for the completed motorcycle☆

This time the sheet is complete.
This time, I painted the diamond mark on the seat and covered the seat.

 

Prince Purple Rain motorcycle replica Honda CM400T

Prince Purple Rain motorcycle replica Honda CM400T

It turned bright red.

Sew in a diamond shape.　Sew with the sponge in between.

Prince Purple Rain motorcycle replica Honda CM400T

The surface was wrinkled.

It’s behind the seat base.

I sprayed it with a rust preventative.

Add molding to the edges to prevent the sheet from tearing.

Cover with vinyl to prevent water from entering.

It is difficult to stretch the sheet.

It’s dangerous, so put a cap on the screw.

Prince Purple Rain motorcycle replica Honda CM400T

Finally completed.

Prince Purple Rain motorcycle replica Honda CM400T

Prince Purple Rain motorcycle replica Honda CM400T

Prince Purple Rain motorcycle replica Honda CM400T

Apply silicone to the seams to keep water out.

Prince Purple Rain motorcycle replica Honda CM400T

It was a tough job, but the motorcycle seat is finally finished！(*^^*)

☕️ Support This Project

Thank you so much for reading to the end!
This Prince’s “Purple Rain” motorcycle replica was completed after 2 years of hard work in Japan.
If you enjoyed this restoration journey and want to help me keep this English blog alive, please consider buying me a coffee. Your support means the world to me!



⚡️ Buy me a coffee 



～archive～
☆Click here for the completed motorcycle☆
Building a Prince’s “Purple Rain” motorcycle Replica㉑
Building a Prince’s “Purple Rain” motorcycle Replica⑳
Building a Prince’s “Purple Rain” motorcycle Replica⑲
Building a Prince’s “Purple Rain” motorcycle Replica⑱
Building a Prince’s “Purple Rain” motorcycle Replica⑰
Building a Prince’s “Purple Rain” motorcycle Replica⑯
Building a Prince’s “Purple Rain” motorcycle Replica⑮
Building a Prince’s “Purple Rain” motorcycle Replica⑭
Building a Prince’s “Purple Rain” motorcycle Replica⑬
Building a Prince’s “Purple Rain” motorcycle Replica⑫
Building a Prince’s “Purple Rain” motorcycle Replica⑪
Building a Prince’s “Purple Rain” motorcycle Replica⑩
Building a Prince’s “Purple Rain” motorcycle Replica⑨
Building a Prince’s “Purple Rain” motorcycle Replica⑧
Building a Prince’s “Purple Rain” motorcycle Replica⑦
Building a Prince’s “Purple Rain” motorcycle Replica⑥
Building a Prince’s “Purple Rain” motorcycle Replica⑤
Building a Prince’s “Purple Rain” motorcycle Replica④
Building a Prince’s “Purple Rain” motorcycle Replica③
Building a Prince’s “Purple Rain” motorcycle Replica②
Building a Prince’s “Purple Rain” motorcycle Replica①

-English edition

執筆者：

comment

Your email address will not be published. Required fields are marked *

CAPTCHA


関連記事

Building Prince’s Purple Rain Motorcycle Replica (Honda CM400T Custom) in Japan – No. 15

I’m building a motorcycles for Prince “Purple Rain”（No. 15） ☆Click here for the First article ☆ ☆Click here for the completed motorcycle☆ Continuation of cowling production.　Since the plating of the side blinker had deteriorated, I decided to put a plating sheet on it. Lightly sand the whole thing. I tried pasting the plated sheet, but the corner part can’t be pasted well.　Trial and error, but crumpled. I decided to give up the plated sheet and paint it with silver.　Scrape off the plated part to remove the step.　I use instant glue instead of putty. I blew primer, blew surfacer, and painted …

Building Prince’s Purple Rain Motorcycle Replica (Honda CM400T Custom) in Japan – No. 11

I’m building a motorcycles for Prince “Purple Rain”（No. 11） ☆Click here for the First article ☆ ☆Click here for the completed motorcycle☆ This time, we processed the stay of the sissy bar and adjusted the mounting. Above is the previous state.　The shape is different from “Purple Rain”, so I made it with a new iron plate. I cut the previous stay by myself, but the shape was not good. The stay I made this time is sharper than before. It’s also lightweight. Drill holes for mounting. The main body is also cut a little so that the stay does not …

Building Prince’s Purple Rain Motorcycle Replica (Honda CM400T Custom) in Japan – No. 13

I’m building a motorcycles for Prince “Purple Rain”（No. 13） ☆Click here for the First article ☆ ☆Click here for the completed motorcycle☆ Last time I made a sissy bar and cowling stay.　I installed a spacer because there was a gap between the sissy bar stay and the main body. Fits without gaps.　The sissy bar fitting is now complete.　After that, just send it to the plating shop. Cut the excess part of the cowl stay to give a sharp impression. Install headlights.　Ported from the conventional cowling. The shape of the light stay differs depending on the type of “Windjammer”.　The “Windjammer 4” …

prince-purple-rain-motorcycle-honda-cm400-build

Building Prince’s Purple Rain Motorcycle Replica (Honda CM400T Custom) in Japan – No. 8

I’m building a motorcycles for Prince “Purple Rain”（No. 8） ☆Click here for the First article ☆ ☆Click here for the completed motorcycle☆ Last time I made some mistakes, but I was able to paint the exterior in a beautiful purple color.　This time, I painted the inside of the cowling black. The cowling before painting is made of black resin. However, it will not be beautiful after 40 years, so I will paint it. I flattened the corners with putty.　There is a hole for a cigar socket, but since it is not used, it will be closed after painting. Apply a …

Building Prince’s Purple Rain Motorcycle Replica (Honda CM400T Custom) in Japan – No. 9

I’m building a motorcycles for Prince “Purple Rain”（No. 9） ☆Click here for the First article ☆ ☆Click here for the completed motorcycle☆ Last time I finished working on the exterior. This time it is wiring adjustment, cowling stay adjustment, sissy bar work. Wrap the wiring near the headlight with food wrap.　It is waterproof. Then wrap it in a plastic sheet for gardening. compact. The mounting position of the cowl and stay is slightly misaligned, so adjustment is required. Take a mold with aluminum foil and make a spacer. I’m thinking of a light and soft spacer. Cut off the excess …

PREV
Building Prince's Purple Rain Motorcycle Replica (Honda CM400T Custom) in Japan - No. 19
NEXT
Building Prince's Purple Rain Motorcycle Replica (Honda CM400T Custom) in Japan - No. 21